Until a couple of years ago CMOS sensors were definitely the underdog, they tended to be very noisy due to electrical noise generated the on chip by the readout circuits and A/D converters. In addition they lacked sensitivity due to the electronics on the face of the chip leaving less room for the light sensitive parts. Today, on chip noise reduction has made it possible to produce CMOS sensors with very low noise and micro lenses and better design has mitigated most of the sensitivity problems. In terms of a static image there is very little difference between a CMOS sensor and a CCD sensor. Dynamic range is remarkably similar (both types of sensor use essentially the same light gathering methods), in some respects CMOS has the edge as they are less prone to overload issues. CCD’s are very expensive to manufacture as the way they are read out requires near lossless transfer of minute charges through a thousand or more (for HD) memory cells. The first pixel to be read passes down through over 1000 memory cells, if it was to loose 5% of it’s charge in each cell, the signal would be seriously reduced by the time it left the chip. The last pixel to be read out only passes through one memory cell, so it would be less degraded, this variation could ruin an image making it uneven. Although there is more electronics on a CMOS sensor, as each pixel is read directly a small amount of loss in the transfer is acceptable as each pixel would have a similar amount of loss. So the chips are easier to make as although the design is more complex, it is less demanding and most semiconductor plants can make CMOS sensors while CCD needs much more specialised production methods. Yes, CMOS sensors are more prone to motion artifacts as the sensor is scanned from top to bottom, one pixel at a time (A CCD is read in it’s entirety just about instantaneously). This means that as you pan, at the start of the pan the top of the sensor is being read and as the pan progresses the scan moves down the chip. This can make things appear to lean over and it’s known as skew. The severity of the skew is dependent on the readout speed of the chip. Stills cameras and mobile phone cameras suffer from terrible skew as they typically have very slow readout speeds, the sensors used in an EX have a much higher readout speed and in most real world situations skew is not an issue. However there may be some circumstances where skew can cause problems but my experience is that these are few and far between. The other issue is Flash Banding. Again this is caused by the CMOS scan system. As a flash gun or strobe light is of very short duration compared to the CMOS scan it can appear that only part of the frame is illuminated by the flash of light. You can reduce the impact of Flash Banding by shooting at the slowest possible shutter speed (for example shooting 25P or 24P with no shutter) but it is impossible to completely eliminate. When I shoot lightning and thunderstorms I often use a 2 frame shutter, shooting this way I get very few partial bolts of lightning, maybe 1 in 50. If you shoot interlace then you can use the Flash Band removal tool in Sony’s Clip Browser software to eliminate flash gun problems. CMOS sensors are becoming much more common in high end cameras. Arri’s new Alexa film replacement camera uses a CMOS sensor rated at 800asa with 13 stops of latitude. Red uses CMOS as does SI2K. Slumdog Millionaire (SI2K) was the first electronically shot film to get an Oscar for cinematography, so certainly CMOS has come a long way in recent years. CMOS is here to stay, it will almost certainly make bigger and bigger inroads at higher levels. Read speeds will increase and skew etc will become less of an issue. IMHO skew is not an issue to loose sleep over with the EX’s anyway. I shoot all sorts from hurricanes and tornadoes to fast jets and race cars. I have yet to come across a shot spoilt by skew, generally motion blur tends to mask any skew long before it gets noticeable. If you shoot press conferences or red carpet events where flash guns will be going off, then you may prefer a CCD camera as this is harder to deal with, but the EXs are such good value for the money and bring many other advantages such as lower power and less weight that you have to look at the bigger picture and ask what you expect from your budget.
All posts by alisterchapman
PMW-350 Scene Files for Download
PMW-350 Scene Files for Download
Click on the link above to download a set of my latest scene files. Un-zip and copy to the root of an SxS card, the in the file menu load the files.
These are mainly matrix tweeks. neut2 is one I like that gives rich primary colours while still reasonably true to life. Cine1 is a sudo filmic look Film1 is meant to emulate well saturated film stock DSC-1 is based on Chroma-Du-Monde chart for accurate daylight color Neut is my first matrix tweak for a less green look and warmer skin tones.
Vapour: The Sky in motion.
The last couple of days provided some really spectacular skies with amazing vapor trails and fluffy clouds. So I grabbed a selection of cameras and shot a bunch of timelapse which you can see cobbled together in this clip. I used a Sony PMW-350 and a Canon 350D and 550D. Amazing how well they match after a quick grade. I also included an previously un-used Aurora shot from Iceland at the end. The name of the clip comes from the fact that clouds are made of water vapor and ice crystals.
You can also watch it in HD on Exposure Room.
Canon T2i, first impressions, initial tests (frame grabs and video supplied).
As you may have seen from my earlier post I became the owner of the new Canon T2i (or 550D as it’s known in the UK) at the weekend. Clearly before using any camera in anger it’s important to see what it can and can’t do. I will say that I am not a Canon DSLR expert. I have been following the fuss and much admire some of the work done with these cameras by Phil Bloom, but frankly after playing with the Canon over the weekend I have to say I’m disappointed. Yes you can achieve shallow depth of field very easily and you do get a filmic look to the pictures, but look at the footage on a big monitor and it just looks soft. At first I wondered if this was the lens I was using, so I tried a couple of others including a nice Tamron 28mm prime. I tried different apertures, shutter speeds etc, but every clip I’ve taken looks soft. In isolation, on scenes with low detail this isn’t immediately apparent, but anything with lots of fine detail looks soft. Some of this is aliasing, look at the roof of the house in the T2i image, it appears to have diagonal roof tiles, this is a pretty typical aliasing artifact. I shot some closer shots of the buildings and the brickwork aliased like crazy.
Looking at the flowers picture you can see that the EX1 has picked up more of the subtle texture, or at least it has recorded more of the texture. I’m sure some of the Canon’s softness is due to compression artifacts. The other thing that I found is that it is tending to crush blacks a bit. I have played around with the picture styles and you can reduce this a bit, but there is very little detail in deep blacks, which would IMHO make grading tricky. The one good thing I did find was that it is very noise free at 200 and 400 asa, it’s also useable up to 800 asa or at a push 1600asa, so it would make a good camera for very low key scenes, provided you use a good fast lens. Looking at the Canon pictures there was something pleasing about the deep, almost crushed blacks. I think this helps contribute to the Canon DSLR “look” so I quickly threw together a new picture profile for the EX1/3 and PMW-350, but I’m afraid that the details of that will be the subject of another post, as I have work that I must do first! The EX images in the frame grabs were shot with this picture profile. As we all know the ergonomics of the video DSLR’s is pretty poor for video. It’s tricky to hold and you have to use an add on Loupe to make the LCD useable as a viewfinder. You can’t zoom mid shot and without peaking or zebras adjusting exposure and focus accurately is difficult. I was hoping to be able to use the 550D as a B camera for those situations where I need a small, discreet camera, but having seen the pictures, so far, for me it will be reserved for holidays and shooting where you not supposed to video and for shoots where supper shallow DoF is essential. I have to say I’m really disappointed, I wanted this camera to be so much better, I knew it would suffer from aliasing, but I wasn’t expecting the soft pictures, I guess some will say that the softness adds to the filmic look, but I’d much rather do that with some nice pro-mists or filtration in post production rather than starting out with soft pictures. Perhaps I’ve done something wrong? If I have please add a comment!
UPDATE: I was so convinced that I must be doing something wrong that I shot some more clips, this time with less harsh lighting. No, change however, the T2i is still soft and the new clips show just how big a problem aliasing is. You have to consider that the coloured moire patterns are recorded like that, no amount of grading will get rid of it. A small amount of diffusion on the camera should help, but then your going to have to work out how much to soften and diffuse each shot to make sure your not making the pictures even softer than they already are.
The frame grabs are all 1:1 pixel for pixel, no trickery has been used! You can download some further examples by clicking here. Even if you were shooting stuff for the web this level of aliasing could cause big problems as it’s really obvious. For this shot I had the Canons sharpness setting turned all the way down. I have also turned down the contrast setting as this gives better dynamic range with less crushed blacks. My workflow is to import the H264 files from the camera and then convert them to ProResHQ. This helps a little with sharpness over working with the native H264, but for me this last test was the nail in the coffin for DSLR’s as footage like this would simply be unusable. If you watch the YouTube clip please make sure you watch it full screen or at least at the 480P setting. The small embedded size doesn’t show the aliasing as much as the bigger versions.
FURTHER UPDATE:
OK, so it’s defiantly not just me doing something wrong. When in focus the T2i/550D aliases (as do all the current Canon DSLR’s). This is a grab from Philip Blooms latest Canon short. For once this is a daylight piece and as I expected it exhibits a lot of aliasing. The grab is actually taken from the thumbnail on his exposure room page. I’m really pleased to see this as it shows that aliasing is a problem for the experts too. You start to appreciate why so many of the Canon shorts are shot at night, with millimeter deep DoF… it’s to stay clear of having stuff in focus that will alias. there are filters from Caprock that are supposed to help, but you need a different filter for each focal length and aperture that you use, they also soften the picture somewhat.
If you want my opinion, then it has to be that the Canon’s are close, but still a mile away. The aliasing issue is a biggie. Sort it out and the skew, jello and overheating can be worked around, but if you have to worry about simply having a piece of wood in focus and whether it’s going to exhibit rainbows of colour or whether cobble stones will twitter and change colour (At 00.35 and this is from Canon) then it will limit what you can do. There is quite a lot of aliasing in Phil’s new daytime clip, basically anytime anything is steady, has texture and is in focus, it aliases. I’ve been shot down in flames on other forums for saying that this is a problem, but if even the experts can’t deal with it then what hope does everyone else have? I would love to have the option of shooting with the shallow DoF that the Canon’s offer, but not at the expense of having to avoid any kind of texture. Perhaps Red and Scarlet will be better, perhaps Canon will sort it out, or perhaps not, as the cameras are clearly selling like hot cakes, even with the issues. If they do fix it then the camera will almost certainly be for video only.
Canon T2i, first impressions, initial tests (frame grabs and video supplied).
As you may have seen from my earlier post I became the owner of the new Canon T2i (or 550D as it’s known in the UK) at the weekend. Clearly before using any camera in anger it’s important to see what it can and can’t do. I will say that I am not a Canon DSLR expert. I have been following the fuss and much admire some of the work done with these cameras by Phil Bloom, but frankly after playing with the Canon over the weekend I have to say I’m disappointed. Yes you can achieve shallow depth of field very easily and you do get a filmic look to the pictures, but look at the footage on a big monitor and it just looks soft. At first I wondered if this was the lens I was using, so I tried a couple of others including a nice Tamron 28mm prime. I tried different apertures, shutter speeds etc, but every clip I’ve taken looks soft. In isolation, on scenes with low detail this isn’t immediately apparent, but anything with lots of fine detail looks soft. Some of this is aliasing, look at the roof of the house in the T2i image, it appears to have diagonal roof tiles, this is a pretty typical aliasing artifact. I shot some closer shots of the buildings and the brickwork aliased like crazy.
Looking at the flowers picture you can see that the EX1 has picked up more of the subtle texture, or at least it has recorded more of the texture. I’m sure some of the Canon’s softness is due to compression artifacts. The other thing that I found is that it is tending to crush blacks a bit. I have played around with the picture styles and you can reduce this a bit, but there is very little detail in deep blacks, which would IMHO make grading tricky. The one good thing I did find was that it is very noise free at 200 and 400 asa, it’s also useable up to 800 asa or at a push 1600asa, so it would make a good camera for very low key scenes, provided you use a good fast lens. Looking at the Canon pictures there was something pleasing about the deep, almost crushed blacks. I think this helps contribute to the Canon DSLR “look” so I quickly threw together a new picture profile for the EX1/3 and PMW-350, but I’m afraid that the details of that will be the subject of another post, as I have work that I must do first! The EX images in the frame grabs were shot with this picture profile. As we all know the ergonomics of the video DSLR’s is pretty poor for video. It’s tricky to hold and you have to use an add on Loupe to make the LCD useable as a viewfinder. You can’t zoom mid shot and without peaking or zebras adjusting exposure and focus accurately is difficult. I was hoping to be able to use the 550D as a B camera for those situations where I need a small, discreet camera, but having seen the pictures, so far, for me it will be reserved for holidays and shooting where you not supposed to video and for shoots where supper shallow DoF is essential. I have to say I’m really disappointed, I wanted this camera to be so much better, I knew it would suffer from aliasing, but I wasn’t expecting the soft pictures, I guess some will say that the softness adds to the filmic look, but I’d much rather do that with some nice pro-mists or filtration in post production rather than starting out with soft pictures. Perhaps I’ve done something wrong? If I have please add a comment!
UPDATE: I was so convinced that I must be doing something wrong that I shot some more clips, this time with less harsh lighting. No, change however, the T2i is still soft and the new clips show just how big a problem aliasing is. You have to consider that the coloured moire patterns are recorded like that, no amount of grading will get rid of it. A small amount of diffusion on the camera should help, but then your going to have to work out how much to soften and diffuse each shot to make sure your not making the pictures even softer than they already are.
The frame grabs are all 1:1 pixel for pixel, no trickery has been used! You can download some further examples by clicking here. Even if you were shooting stuff for the web this level of aliasing could cause big problems as it’s really obvious. For this shot I had the Canons sharpness setting turned all the way down. I have also turned down the contrast setting as this gives better dynamic range with less crushed blacks. My workflow is to import the H264 files from the camera and then convert them to ProResHQ. This helps a little with sharpness over working with the native H264, but for me this last test was the nail in the coffin for DSLR’s as footage like this would simply be unusable. If you watch the YouTube clip please make sure you watch it full screen or at least at the 480P setting. The small embedded size doesn’t show the aliasing as much as the bigger versions.
FURTHER UPDATE:
OK, so it’s defiantly not just me doing something wrong. When in focus the T2i/550D aliases (as do all the current Canon DSLR’s). This is a grab from Philip Blooms latest Canon short. For once this is a daylight piece and as I expected it exhibits a lot of aliasing. The grab is actually taken from the thumbnail on his exposure room page. I’m really pleased to see this as it shows that aliasing is a problem for the experts too. You start to appreciate why so many of the Canon shorts are shot at night, with millimeter deep DoF… it’s to stay clear of having stuff in focus that will alias. there are filters from Caprock that are supposed to help, but you need a different filter for each focal length and aperture that you use, they also soften the picture somewhat.
If you want my opinion, then it has to be that the Canon’s are close, but still a mile away. The aliasing issue is a biggie. Sort it out and the skew, jello and overheating can be worked around, but if you have to worry about simply having a piece of wood in focus and whether it’s going to exhibit rainbows of colour or whether cobble stones will twitter and change colour (At 00.35 and this is from Canon) then it will limit what you can do. There is quite a lot of aliasing in Phil’s new daytime clip, basically anytime anything is steady, has texture and is in focus, it aliases. I’ve been shot down in flames on other forums for saying that this is a problem, but if even the experts can’t deal with it then what hope does everyone else have? I would love to have the option of shooting with the shallow DoF that the Canon’s offer, but not at the expense of having to avoid any kind of texture. Perhaps Red and Scarlet will be better, perhaps Canon will sort it out, or perhaps not, as the cameras are clearly selling like hot cakes, even with the issues. If they do fix it then the camera will almost certainly be for video only.
XDCAM EX Firmware for new cards.. Available now!
Sony have just released the firmware required to use the new 32Gb SxS-1 cards, the Memory Stick and SD Card adapters. This firmware also adds the ability to have much longer clip titles (46 Characters!) on the PMW-350 and EX1R. You can do the update yourself, you don’t have to send the camera back to Sony (hooray) to do the update. CLICK HERE to go to the firmware on the Sony UK site. Initial reports indicate that the update improves the performance of 3rd party SD card adapters and is straight forward to install. There are also indications that original EX3?s boot up a bit faster. At the moment the EX1 update appears to be missing from the download page, but I have been assured this will be rectified in the next 24 hours.
How I shoot the Northern Lights
Well I have just returned from Iceland where I held a couple of 3D stereoscopic master classes and a workshop on video for the internet. They went well and we all had fun despite almost a foot of snow fall the morning of the classes. On the last day of my trip I decided to try and get some more Northern Lights footage. As I am often asked how I do this I put together the clip below which explains what settings I use for the Aurora and also gives a brief description of S&Q on an XDCAM EX. Basically what I do is use the EX Slow Shutter at 32 or 64 frames to increase the sensitivity of the camera. For a dim Northern Lights display I use 64 frames but for a bright display I drop down to 32 frames. The slow shutter acts like a long exposure on a stills camera. I then combine this with interval record shooting at 1 frame every second. I did also have a Canon DSLR with me and tried to shoot the Aurora with that. I found I needed a 10 second exposure at 800 asa to get a similar result to that achieved with the EX. The 10 second exposure means that it would take longer to get a decent length video sequence and most of the motion of the Aurora would be lost. Some of the exposure difference was I admit to the slower F4 lens on the Canon compared to the Sony EX’s F1.8, so perhaps with a faster lens you could bring the exposure down to around 5 seconds and this is something I hope to try when I go Aurora chasing next winter.
If you watch the video make sure you stay to the end to check out my attempt to record a piece to camera in 60 mph blowing snow! Don’t know why I even thought it would work. What I will say is that my new Vinten 5AS did a great job of keeping the camera steady in some pretty extreme conditions.
Brewing up a Scene File: Gamma and Knee
Brewing up a Scene File: Gamma and Knee
Before anyone complains that I have missed stuff out or that some technical detail is not quite right, one of the things I’m trying to do here is simplify the hows and why’s to try and make it easier for the less technical people out there. Lets face it this is an art form, not a science (well actually a bit of both really).
So what is a gamma curve anyway? Well the good old fashioned cathode ray tube television was a very non-linear device. You put 1 unit of power in and get one unit of light out. You put 2 units in and get 1.5 units out, put 3 in and get 2 out… and so on. So in order to get a natural picture the output of the camera also has to be modified to compensate for this. This compensation is the gamma curve, an artificial modification of the output signal from the camera to make it match TV’s and monitors around the world. See Wikipedia for a fuller explaination: http://en.wikipedia.org/wiki/Gamma_correction
So, all video cameras will have a gamma curve, whether you can adjust it or not is another matter. Certainly most pro level cameras allow you some form of gamma adjustment.
The PMW-350 has 6 standard gamma curves, these are all pretty similar, they have to be otherwise the pictures wouldn’t look right, but small changes in the curve effect the relationship between dark and bright parts of the pictures. Todays modern cameras have a far greater dynamic range (range of dark to bright) than older cameras. This means that the full dynamic range of the sensor no longer fits within the gamma curves used for TV’s and monitors. In broadcast television any signal that goes over 100% gets clipped off and is discarded, so the cameras entire brightness range has to be squeezed into 0 to 100%. The PMW-350 sensors are capable of far more than this (at least 600%) so what can you do?
The older and simpler solution is called the “Knee”. The knee works because in most cases the brightest parts of a scene contains little detail and is generally ignored by our brains. We humans tend to focus on mid-tone faces, animals and plants rather than the bright sky. Because of this you can compress the highlights (bright) parts of the picture quite heavily without it looking hugely un-natural (most of the time at least). What the knee does is takes a standard gamma curve and up near it’s top, bends it over. This has the effect of compressing the brighter parts of the image, squashing a broad range of highlights (clouds for example) into a narrow range of brightness. While this works fairly well, it does tend to look rather “electronic” as the picture is either natural (below the knee) or compressed (above the knee).
The answer to this electronic video look is to replace the hard knee with gentle bend to the gamma curve. This bend starts some way down the gamma curve, very gentle at first but getting harder and harder as you go up the gamma curve. This has the effect of compressing the image gently at first with the compression getting stronger and stronger as you go up the curve. This looks a lot more natural than a hard knee and is far closer to the way film handles highlights. The downside is that because the compression starts earlier a wider tonal range is compressed. This makes the pictures look flat and uninteresting. You have to watch exposure on faces as these can creep into the compressed part of the curve. The plus point is that it’s possible to squeeze large amounts of latitude into the 100% video range. This video can then be worked on in post production by the editor or colorist who can pull out the tonal range that best suits the production.
These compressed gamma curves are given different names on different products. Panasonic call them “Film Rec”, on the EX1 they are “Cinegammas” on the PMW-350 they are “Hypergammas”. The 350 has four Hypergammas. The first is 3250. this takes a brightness range the equivalent to 325% and compresses it down to 100%. HG 4600 takes 460% and squeezes that down to 100%. Both of these Hypergammas are “broadcast safe” and the recordings made with them can be broadcast straight from the camera without any issues. The next Hypergamma is 3259. This takes a 325% range and squeezes this down to a 109% range, likewise 4609 takes 460% down to 109%. But why 109%? well the extra 9% gives you almost 10% more data to work with in post production compared to broadcast safe 100%. It also gives you the peak white level you need for display on the internet. Of course if you are doing a broadcast show you will need to ensure that the video levels in the finished programme don’t exceed 100%.
My preferred gamma is Hypergamma 4 (4609) as this gives the maximum dynamic range and gives a natural look, however the pictures can look a little flat so if I’m going direct from the camera to finished video without grading I use either a standard gamma or use the Black Gamma function to modify the curve. I’ll explain the Black Gamma in my next post.
There are 6 standard gammas to choose from. I like to stick with gamma 5 which is the ITU-709 HD standard gamma. To increase the dynamic range I use the Knee. The default knee point setting is 90, this is a reasonable setting, but if your shooting with clipping set to 100% you are not getting all the cameras latitude (the Knee at 90 works very well with clipping at 108%). Lowering the knee down to 83 gives you almost another stop of latitude, but you have to be careful as skin tones and faces can creep up towards 83%. It’s very noticeable if skin becomes compressed so you need to watch your exposure. This is also true of the Hypergammas and with them you may need to underexpose faces very slightly. The other option is to set the knee point to 88 and then also adjust the knee slope. The slope is the compression amount. A positive value is more compressed, negative less compressed. With the knee at 88 and slope set to +20 you get good latitude, albeit with quite highly compressed highlights.
If you want to play with the gammas and knee and see how they work one method you can use is to use a paint package on your PC (such as photoshop) to create a full screen left to right graduated image going from Black to white. Then shoot this with the camera (slightly out of focus) while making adjustments to the curves or knee and record the results along with a vocal description of each setting. Import the clips into your favorite editing package and use the waveform monitor or scopes you should be able to see a reasonable representation of the shape of the gamma curve and knee.
So my Gamma Choices are:
For material that will be post produced: Hypergamma 4609 (HG4)
For material that will be used straight from the camera: Standard Gamma 5 Knee at 90 with clip at 108% for non broadcast or Knee at 88 with slope +20 with white clip at 100% for direct to broadcast.
PMW-350 Aperture Correction what is it doing?
After completing the multi camera shootout at Visual Impact, one thing was bothering me about the pictures from the PMW-350 and that was the way the specular highlights in the tin foil were artificially enhanced. During the test the camera was set to factory defaults, which IMHO are too sharp, but the foil in particular looked nasty. Since then I have been further refining my paint settings for the 350 and looking at detail and aperture. Today I was replicating the tin foil test and looking at the aperture settings (not the knee aperture) and I noticed that turning aperture on and off had a very pronounced effect on highlights but a much smaller effect elsewhere in the image. Normally I would expect the aperture setting to act as a high frequency boost making subtle textures more or less enhanced, which it does, but the amount of enhancement appears to vary with the brightness of the image with specular highlights getting a really big hit of correction. If you look at the images to the left at the top you have aperture correction on at +99. There are big ugly black lines around the highlights on the foil and the texture of the carpet has been enhanced. To some degree this is the expected behaviour although I am surprised by how thick the edges around the highlights are, this looks more like detail correction (it could be “ringing”). The middle images are aperture off, not zero but actually off and you can see that the edges on the foil have gone and the carpet is no longer enhanced. The bottom picture though with aperture on at -99 though is very interesting as the carpet appears slightly softer than OFF, which is not unexpected while the foils is sharper than OFF and this is not expected. I don’t like this behaviour I’m afraid to say as a typical way to get a filmic look from a video camera is to turn the detail correction off to give a natural picture and then use Aperture correction to boost high frequencies to retain a sharp image. On the PMW-350 you can’t do this as this as a high Aperture setting will give you those nasty edges on highlights. So what can you do? Well the 350?s native, un-enhanced resolution is very high anyway so it doesn’t need a lot of correction or boosting. The default Detail and Aperture settings will give some really nasty highlight edges so you need to back things off. If your going for a filmic look I would turn OFF aperture correction altogether, for video work with pictures that have some subtle enhancement I would use Aperture at around -20, certainly never higher than -15 unless you like black lines around specular highlights.
My current prefered detail, aimed at giving a very slight, not obvious enhancement are are as follows:
Detail Level -12, H-V Ratio +15, Crispening 0, Frequency +30, White Limit +30, Black Limit +40 (all other detail settings at default)
Aperture OFF for filmic look, Aperture -20 for video look.
I have also made some changes to the Matrix settings. I have been finding the pictures from Sony cameras to be a little on the Green/Yellow side so I have tweaked things a little to remove the yellow cast and put in a bit of red, this is a subtle change but really helps with skin tones, stopping on screen talent from looking ill! These settings work in the PMW-350, EX1/3 and PDW-700.
On an EX1/EX3 this works best with the Standard Matrix, On a PMW-350 or PDW-700 you can use it on it’s own or mix it with one of the preset matrices as a modifier. User Matrix On, R-G 0, R-B +5, G-R -6, G-B +8, B-R -15, B-G -9
Have Fun!
PMW-350 sample footage from Norway
I have uploaded a further selection of clips from the PMW-350 shot in Norway to YouTube. It’s also on Exposure Room if you want better quality.